Effect of Low-speed Wire Cut Electrical Discharge Machining on the Bending Strength of Ti(C,N)-based Cermet AITranslate
Abstract AITranslate
The effect of low-speed wire cut electrical discharge machining （WEDM-LS） on the bending strength of Ti（C,N）-based cermet of Ti（C,N）-7%WC -20%Ni-7%Mo was studied by hydraulic universal testing machine. The morphology and chemical composition of the machining surface, and the microstruc- ture of the deterioration layer were observed and analyzed by SEM and EDS. The results show that WEDM -LS causes obvious electrical erosion deterioration layer, significantly reducing the bending strength and increasing the intensity dispersion of the sample. There are a large number of microscopic defects such as micro-cracks,holes and grain shedding in microstructure of the deterioration layer.
KeyWords AITranslate
1郭涛,王笃诚.关于电火花线切割变质层的研究[J].电子工艺技术,1991(2):40-47. 被引量：2
2刘寿荣.电火花切割加工对WC—Co硬质合金显微结构的影响[J].粉末冶金技术,1991,9(2):83-89. 被引量：1
3绪方,张颖.电火花加工表面的残余应力与变质层[J].国外金属加工,1993(1):19-25. 被引量：1
4贾昌乐,王晓冬,马德通.电加工表面变质层与模具使用寿命[J].电加工,1996(1):18-22. 被引量：8
5郑富强,邹丹,臧海天.硬质合金线切割加工变质层的形成及对材料性能的影响[J].电加工与模具,2009(5):18-20. 被引量：4
6张方圆,段春争,王敏杰.已加工表面变质层的发展研究[J].机械设计与制造,2014(10):265-268. 被引量：4
7郑富强,陈康华,李詠侠,邹丹.基于正交试验的硬质合金电火花加工实验分析[J].模具制造,2016,16(2):68-70. 被引量：3
8孙瑶,巩亚东,刘寅.慢走丝电火花线切割TC4试验研究和参数优化[J].东北大学学报：自然科学版,2016,37(7):979-983. 被引量：9
9郭崇文,李文斌.YG6硬质合金电火花线切割加工工艺参数研究[J].稀有金属与硬质合金,2015,43(3):67-70. 被引量：18
10边留进,林子超,孙方宏,郭松寿.基于正交试验的慢走丝电火花线切割加工的参数优化[J].现代制造工程,2013(10):1-5. 被引量：21
1赵丽丽.机械加工对金属零件加工精度的影响[J].世界有色金属,2019,0(5):227-228. 被引量：2
1杨鲧.机械加工中加工精度的影响因素与控制[J].机电工程技术,2019,48(12):84-85. 被引量：4
2孙波.机械齿轮轴加工工艺与优化研究与发展趋势[J].中国金属通报,2020(13):268-269. 被引量：1
1郭霜,许甲岿,程中甫,付猛.摆线轮慢走丝线切割加工关键技术研究[J].现代制造技术与装备,2018,54(2):85-86. 被引量：2
2激发创想 展望未来[J].现代制造,2017,0(40):62-62.
3樊长昕.不同矿料级配对抗车辙剂沥青混合料高温性能的影响[J].山西交通科技,2017(5):27-30. 被引量：2
4Junichi SUZUMURA,周贤全(译).用导电润滑脂预防滚动轴承电蚀[J].国外铁道车辆,2018,55(2):33-37. 被引量：2
5P.WU,S.C.LIU,X.R.JIANG.Effect of multi-walled carbon nanotube addition on the microstructures and mechanical properties of Ti(C,N)-based cermets[J].先进陶瓷（英文）,2018,7(1):58-63. 被引量：1
6张仁奇.步进电机位置采集在显微缺陷检测系统中的应用[J].通讯世界,2017,23(21):145-146.
7张敏敏,陈森,于泽州,刘赞,陈庸,彭强,李达.沉积行为对电火花沉积Ti(C,N)涂层微结构的调控机制[J].热加工工艺,2018,47(4):159-163. 被引量：2
8杨琦,杨天钧.35CrMo钢汽车螺栓的断裂失效分析[J].铸造技术,2017,38(12):2900-2902. 被引量：3
9肖光春,张衍路,许崇海,孟祥龙.石墨烯增韧Al_2O_3/Ti(C,N)纳米复合陶瓷刀具材料的制备及其微观结构分析[J].齐鲁工业大学学报,2018,32(2):41-44. 被引量：1
10高磊,林鹏.厂拌热再生沥青混合料的最佳RAP掺量研究[J].华东交通大学学报,2018,35(1):103-108. 被引量：18
Basic Information:
DOI：
Chinese Library Classification Number:TF125.31[冶金工程—粉末冶金]
Citation Information:
The effect of low-speed wire cut electrical discharge machining （WEDM-LS） on the bending strength of Ti（C,N）-based cermet of Ti（C,N）-7%WC -20%Ni-7%Mo was studied by hydraulic universal testing machine. The morphology and chemical composition of the machining surface, and the microstruc- ture of the deterioration layer were observed and analyzed by SEM and EDS. The results show that WEDM -LS causes obvious electrical erosion deterioration layer, significantly reducing the bending strength and increasing the intensity dispersion of the sample. There are a large number of microscopic defects such as micro-cracks,holes and grain shedding in microstructure of the deterioration layer.
quote
| GB/T 7714-2015 | [1] ZENG Shou-fu, WANG Xiao-ling, YI Jian-hong. Effect of Low-speed Wire Cut Electrical Discharge Machining on the Bending Strength of Ti(C,N)-based Cermet[J]. Rare Metals and Cemented Carbides, 2018(2): 42-48. |
| MLA | [1] ZENG Shou-fu, et al., "Effect of Low-speed Wire Cut Electrical Discharge Machining on the Bending Strength of Ti(C,N)-based Cermet." Rare Metals and Cemented Carbides, no. 2, 2018, pp. 42-48. |
| APA | [1] ZENG Shou-fu, WANG Xiao-ling, & YI Jian-hong. (2018). Effect of Low-speed Wire Cut Electrical Discharge Machining on the Bending Strength of Ti(C,N)-based Cermet. Rare Metals and Cemented Carbides(2), 42-48. |
| IEEE | [1] ZENG Shou-fu, WANG Xiao-ling, and YI Jian-hong, "Effect of Low-speed Wire Cut Electrical Discharge Machining on the Bending Strength of Ti(C,N)-based Cermet," Rare Metals and Cemented Carbides, no. 2, pp. 42-48, 2018. keywords: {low-speed wire cut electrical discharge machining;Ti（C, N）-based cermet;bending strength;de- terioration layer;grinding} |