daohang fenxiangbox searchbox qikanlogonew daohangnew searchboxnew navrightzone footerzone paper

One Step Closer to Coatings Applications Utilizing Self-Stratification: Effect of Rheology Modifiers AITranslate

Loughborough University;CNRS; University of the Basque Country; University of the Basque Country; Université Claude Bernard Lyon 1; Université Claude Bernard Lyon 1; Université Claude Bernard Lyon 1;CNRS;CNRS; Loughborough University
AITranslate
Publisher: ACS
Share Citation Information Add to Favorites

    Scan to share on WeChat or Moments

Use WeChat scan.
Share with WeChat friends or Moments

Abstract AITranslate

Self-stratification of model blends of colloidal spheres has recently been demonstrated as a method to form multifunctional coatings in a single pass. However, practical coating formulations are complex fluids with upward of 15 components. Here, we investigate the influence of three different rheology modifiers (RMs) on the stratification of a 10 wt % 7:3 w:w blend of 270 and 96 nm anionic latex particles that do not stratify without RM. However, addition of a high molar mass polysaccharide thickener, xanthan gum, raises the viscosity and corresponding Péclet number enough to achieve small-on-top stratification as demonstrated by atomic force microscopy (AFM) measurements. Importantly, this was possible due to minimal particle–rheology modifier interactions, as demonstrated by the bulk rheology. In contrast, Carbopol 940, a microgel-based RM, was unable to achieve small-on-top stratification despite a comparable increase in viscosity. Instead, pH-dependent interactions with latex particles lead to either laterally segregated structures at pH 3 or a surface enrichment of large particles at pH 8. Strong RM–particle interactions are also observed when the triblock associative RM HEUR10kC12 is used. Here, small-on-top, large-enhanced, and randomly mixed structures were observed at respectively 0.01, 0.1, and 1 wt % HEUR10kC12. Combining rheology, dynamic light scattering, and AFM results allows the mechanisms behind the nonmonotonic stratification in the presence of associative RMs to be elucidated. Our results highlight that stratification can be predicted and controlled for RMs with weak particle interactions, while a strong RM–particle interaction may afford a wider range of stratified structures. This takes a step toward successfully harnessing stratification in coatings formulations.

KeyWords AITranslate

colloids stratification selfassembly polymers rheology modifiers
No data

Basic Information:

DOI:https://doi.org/10.1021/acsapm.3c01288

Chinese Library Classification Number:

Citation Information:

Self-stratification of model blends of colloidal spheres has recently been demonstrated as a method to form multifunctional coatings in a single pass. However, practical coating formulations are complex fluids with upward of 15 components. Here, we investigate the influence of three different rheology modifiers (RMs) on the stratification of a 10 wt % 7:3 w:w blend of 270 and 96 nm anionic latex particles that do not stratify without RM. However, addition of a high molar mass polysaccharide thickener, xanthan gum, raises the viscosity and corresponding Péclet number enough to achieve small-on-top stratification as demonstrated by atomic force microscopy (AFM) measurements. Importantly, this was possible due to minimal particle–rheology modifier interactions, as demonstrated by the bulk rheology. In contrast, Carbopol 940, a microgel-based RM, was unable to achieve small-on-top stratification despite a comparable increase in viscosity. Instead, pH-dependent interactions with latex particles lead to either laterally segregated structures at pH 3 or a surface enrichment of large particles at pH 8. Strong RM–particle interactions are also observed when the triblock associative RM HEUR10kC12 is used. Here, small-on-top, large-enhanced, and randomly mixed structures were observed at respectively 0.01, 0.1, and 1 wt % HEUR10kC12. Combining rheology, dynamic light scattering, and AFM results allows the mechanisms behind the nonmonotonic stratification in the presence of associative RMs to be elucidated. Our results highlight that stratification can be predicted and controlled for RMs with weak particle interactions, while a strong RM–particle interaction may afford a wider range of stratified structures. This takes a step toward successfully harnessing stratification in coatings formulations.

quote

GB/T 7714-2015 [1] Timothy J. Murdoch, Baptiste Quienne, Maialen Argaiz, et al. ACS Applied Polymer Materials, 2023(5). DOI:10.1021/acsapm.3c01288.
MLA [1] Timothy J. Murdoch, et al., ACS Applied Polymer Materials, no. 5, 2023, https://doi.org/10.1021/acsapm.3c01288.
APA [1] Timothy J. Murdoch, Baptiste Quienne, Maialen Argaiz, Radmila Tomovska, Edgar Espinosa, Franck D’Agosto, Muriel Lansalot, Julien Pinaud, Sylvain Caillol, & Ignacio MartínFabiani. (2023). ACS Applied Polymer Materials(5). https://doi.org/10.1021/acsapm.3c01288
IEEE [1] Timothy J. Murdoch, Baptiste Quienne, Maialen Argaiz, Radmila Tomovska, Edgar Espinosa, Franck D’Agosto, Muriel Lansalot, Julien Pinaud, Sylvain Caillol, and Ignacio MartínFabiani, ACS Applied Polymer Materials, no. 5, 2023, doi: 10.1021/acsapm.3c01288. keywords: {colloids;stratification;selfassembly;polymers;rheology modifiers}