daohang fenxiangbox searchbox qikanlogonew daohangnew searchboxnew navrightzone footerzone paper
中
Home > Journals > Calphad
‹ Previous Article Next Article ›

Experimental investigation and thermodynamic calculation of the Cu–In–Sb phase diagram AITranslate

D. Manasijević; D. Minić; D. Živković; J. Vřešt’ál; A. Aljilji; N. Talijan; J. StajićTrošić; S. Marjanović; R. Todorović;
University of Belgrade;University of Pristina;University of Belgrade; Masaryk University;University of Pristina;Institute of Chemistry;Institute of Chemistry;University of Belgrade;Institute of Mining and Metallurgy
AITranslate
Publisher: Elsevier
Share Citation Information Add to Favorites

    Scan to share on WeChat or Moments

Use WeChat scan.
Share with WeChat friends or Moments

Abstract AITranslate

The phase diagram of the Cu–In–Sb ternary system is of importance in predicting the interface reaction between In-based solder materials and the Cu substrate. The liquidus surface, invariant equilibria and four vertical sections of the Cu–In–Sb ternary system were calculated by the CALPHAD method using binary thermodynamic parameters included in the COST531 database. Alloys, representing two isopleths from indium corner with molar ratio of copper and antimony equal to 1/3 and 1/1 and two isopleths from antimony corner with molar ratio of indium and copper equal to 3/1 and 1/1 were measured with the DTA (Differential Thermal Analysis) and DSC (Differential Scanning Calorimetry). The experimentally determined phase transition temperatures were compared with calculation results and good mutual agreement was noticed.

KeyWords AITranslate

No data

Basic Information:

DOI：https://doi.org/10.1016/j.calphad.2008.08.002

Chinese Library Classification Number:

Citation Information:

The phase diagram of the Cu–In–Sb ternary system is of importance in predicting the interface reaction between In-based solder materials and the Cu substrate. The liquidus surface, invariant equilibria and four vertical sections of the Cu–In–Sb ternary system were calculated by the CALPHAD method using binary thermodynamic parameters included in the COST531 database. Alloys, representing two isopleths from indium corner with molar ratio of copper and antimony equal to 1/3 and 1/1 and two isopleths from antimony corner with molar ratio of indium and copper equal to 3/1 and 1/1 were measured with the DTA (Differential Thermal Analysis) and DSC (Differential Scanning Calorimetry). The experimentally determined phase transition temperatures were compared with calculation results and good mutual agreement was noticed.

quote

GB/T 7714-2015 [1] D. Manasijević, D. Minić, D. Živković, et al. Calphad, 2009(33). DOI:10.1016/j.calphad.2008.08.002.
MLA [1] D. Manasijević, et al., Calphad, no. 33, 2009, https://doi.org/10.1016/j.calphad.2008.08.002.
APA [1] D. Manasijević, D. Minić, D. Živković, J. Vřešt’ál, A. Aljilji, N. Talijan, J. StajićTrošić, S. Marjanović, & R. Todorović. (2009). Calphad(33). https://doi.org/10.1016/j.calphad.2008.08.002
IEEE [1] D. Manasijević, D. Minić, D. Živković, J. Vřešt’ál, A. Aljilji, N. Talijan, J. StajićTrošić, S. Marjanović, and R. Todorović, Calphad, no. 33, 2009, doi: 10.1016/j.calphad.2008.08.002.